• precision pliers for very fine assembly and repair work in electronics
• for bending a nd cutting off wire ends on components
• sturdy, zero backlash box joint
• smooth ground gripping surfaces
• edges carefully deburred
• low-friction double spring for gentle an d even opening
• The mirror polish in combination with a fine oil film provides rust protectio n - no circuit faults caused by peeling chrome from plated tools
• to bend and cut wire at 1.6 mm length below the board

• with precision cutting edges for soft, hard and piano wire
• cuts bolts, nails, rivets , etc. up to Ø 5.2 mm
• efficient joint design ensures exceptional cutting performance with li ttle effort
• with recess for easier cutting of thicker wires
• cutting edges additional ly induction-hardened, cutting edge hardness approx. 64 HRC

• for cutting thin walled plastic pipes (conduit plastic pipes) and flexible hoses, also with fabric reinforcement, of plastic and rubber up to Ø 25 mm / 1"
• not suitable for cutting cabl es
• With opening spring and locking device

• Pinch guard prevents operators' fingers being pinched
• time-saving, precise adjustmen t of the gripping width directly on the workpiece at the push of a button
• less effort requir ed due to self-locking action
• no unintentional shifting of the pliers handles
• high w ear resistance due to the additionally hardened teeth
• maximum load capability thanks to comp letely hardened handles
• Gripping jaws with specially hardened teeth, hardness approx. 56 HRC

• ideal for tightening and loosening siphon screw connections, plastic pipe fittings and round union nuts
• Fine adjustment for ideal adjustment to diverse diameters
• For connectors , oil filters, plastic pipes and siphons
• Robust, heavy duty
• for connectors and coupl ings with screw connection, such as Cannon circular connectors
• for gentle loosening of hoses on nozzles and filter cartridges
• Optimum adhesion on dirt-, oil- and fatfree surfaces
< li>25-way adjustable box joint
• ergonomic handle geometry
• Changeable gripping jaws wi th two-component plastic insert with a hard carrier component (red) and a soft adhesive component (b lue)
• with exchangeable plastic jaws for sensitive surfaces
• up to Ø 75 mm

• cuts finest strands as well as multi-core cables and piano wires
• Powerful, light and universal
• high cutting performance with minimum effort due to optimum coordination of the c utting edge angle and transmission ratio
• Box-joint design: highest stability with low weight
• doubly supported joint axis for heavy duty
• large opening width for thicker cables
• cuts precisely, even through fine copper wires
• compact, low-weight construction
< li>universally usable, in the assembly, maintenance and production
• 40% less force required c ompared with standard diagonal cutters of the same length
• Pliers with integrated, insulated tether attachment point for a tool tether

Meets your requirements: Yellow hammer head / medium-hard: e.g. for tool and machine engineering, car repairs, sheet metal and assembly work.

Simplifies your work: Makes work easier, optimum impact effect and less effort needed.

Protects your health: Deadblow Hammering without recoil minimises loads on joints, tendons and muscles.

Product dimensions: 310 x 130 x 45 mm (LxWxD)

Application: Ideal for delivering measured positioning blows on components such as work pieces in machine vices or for installation work. Medium-hard hammer heads eminently suitable for tool and machine engineering, car repairs as well as sheet metal and assembly work.

Extra: With cast iron balls inside the hammer head for recoilless work.

Choosing the right hammer is particularly important on sensitive surfaces to prevent damage. With its steel tube handle, the no-recoil soft-faced hammer allows the user to deliver measured positioning blows, protecting delicate surfaces and edges through its high-impact effect. Thanks to the special metal filling in the hammer head, the soft-faced hammer also guarantees absolutely no recoil, thus protecting joints. Around 25% more hammer head mass ensures additional power. The yellow medium-hard hammer faces are ideal for universal use in areas such as tool and machine engineering as well as sheet metal and assembly work. The hammer is also impressive due to its steel tube handle with ergonomic, non-slip grip. Each hammer head is available individually as a spare part.

Saves space: Compact and space-saving solution.

Product dimensions: 245 x 85 x 17 mm (LxWxD)

Extra: Simple, rapid operation with solid stopping point for L-keys.

Extra: Common key sizes are stored in the holder where they are easily seen.

Blade: Chrome-vanadium steel, through-hardened, bronzed.

Based on ISO 2936L.

Content:

• 1x L-keys Hex , black oxidised 1.5 mm x 91 mm (06059)
• 1x L-keys Hex , black oxidised 2.0 mm x 101 mm (06361)
• 1x L-keys Hex , black oxidised 2.5 mm x 113 mm (06362)
• 1x L-keys Hex , black oxidised 3.0 mm x 128 mm (06363)
• 1x L-keys Hex , black oxidised 4.0 mm x 142 mm (06364)
• 1x L-keys Hex , black oxidised 5.0 mm x 163 mm (06365)
• 1x L-keys Hex , black oxidised 6.0 mm x 184 mm (06366)
• 1x L-keys Hex , black oxidised 8.0 mm x 206 mm (06368)
• 1x L-keys Hex , black oxidised 10.0 mm x 231 mm (06369)
• 1x Classic holder

Meets your requirements: White hammer head / very hard: e.g. for building and construction, mould construction, road construction, gardening and landscaping.

Simplifies your work: Makes work easier, optimum impact effect and less effort needed.

Lowers your costs: Ergonomic hickory wooden handle and hammer head both available as spare parts.

Product dimensions: 360 x 131 x 57 mm (LxWxD)

Application: Building and construction industries, foundry, mould making, road work, forestry and agriculture, gardening and landscaping.

GS tested.