Dreusicke offers the fine tools you will need for the maintenance and repair of office machines, computers, electronic and/or fine-mechanical devices. (for commercial users only)
- for very tough, continuous use
- high cutting performance with minimum effort due to o ptimum coordination of the cutting edge angle and transmission ratio
- precision cutting edges additionally induction-hardened (cutting edge hardness approx. 64 HRC), for all sorts of wire inclu ding piano wire
- for crush-free cutting of plastic, rubber and soft timber sections
- also for ribbon cable
- exchangeable cutting base with try square for 45°-cuts and markings for 60°-, 75°-, an d 90°-cuts
- With opening spring and locking device
- precision pliers for ultra fine cutting work, e. g. in electronics and fine mechanics
- very precisely ground and sharp cutting edg es with very small bevels for exact cutting on delicate electronic components
- also availabl e without bevel for flush cutting
- precision cutting edges additionally induction-hardened, c utting edge hardness approx. 64 HRC
- approx. 20% lighter than conventional electronics pliers
- bolted joint with carefully manufactured joint surfaces for even, low-friction movement thr oughout the entire opening range
- smooth-running double spring for a gentle and even opening< /li>
- ergonomically optimised multi-component handles
- round head
- precision pliers for ultra fine cutting work, e. g. in electronics and fine mechanics
- very precisely ground and sharp cutting edg es with very small bevels for exact cutting on delicate electronic components
- also availabl e without bevel for flush cutting
- precision cutting edges additionally induction-hardened, c utting edge hardness approx. 64 HRC
- approx. 20% lighter than conventional electronics pliers
- bolted joint with carefully manufactured joint surfaces for even, low-friction movement thr oughout the entire opening range
- smooth-running double spring for a gentle and even opening< /li>
- ergonomically optimised multi-component handles
- pointed head
- with precision cutting edges for soft, hard and piano wire
- cuts bolts, nails, rivets , etc. up to Ø 5.2 mm
- efficient joint design ensures exceptional cutting performance with li ttle effort
- cutting edges additionally induction-hardened, cutting edge hardness approx. 64 HRC
- with slim multi-component grips without collar for better handling and easier transport< /li>
- Opening spring and locking device are integrated in the handles for comfortable work and saf e transport
- Wire stripper with cable shears - two essential electrical installation tools in one pair of pliers
- Integrated cable shears for the clean cutting of Cu- and Al-cables without crushing up to Ø 15 mm (5 x 2,5 mm²)
- cutting edges additionally induction-hardened, cutting edge hard ness approx. 57 HRC
- Universal adjustment of the stripping blades by means of a knurled screw
- slim dimensions for easy access
- Stripping of single-, multi- and fine stranded cond uctors with plastic or rubber insulation up to Ø 5 mm or 10 mm² cross-section
- Graduated jaw provides a visual orientation aid when stripping wire in standard lengths (11 mm and 16 mm)
- impact-resistant plastic case
- external dimensions: 345 x 80 x 280 mm (W x H x D)
- foam insert with recesses for tools, 2 crimping dies and 2 locators
- Clever stripping: large capacity range, sharply ground stripping profiles and intuitive posi tioning
- Innovative cutting geometry: easier cutting, especially of flat cables
- Hybri d design: as flat as needle-nose pliers, as wide as combination pliers for high stability with good accessibility
- Precisely ground stripping profiles for solid conductors from 0.75 - 6 mm² and fine-stranded conductors from 0.5 - 4 mm²
- Precise positioning of the wire thanks to locatio n ridges
- Easy cutting of copper and aluminium cables up to Ø 15 mm (1/2")
- Wide, cros s-hatched gripping surfaces for twisting wires
- Milled groove for secure holding and pulling of small work pieces such as nails
- Convex gripping surface on one side for secure gripping o f flat material and gripping area for round material
- Outer edges for deburring pipes
Saves space: Compact and space-saving solution.
Product dimensions: 245 x 85 x 17 mm (LxWxD)
Extra: Simple, rapid operation with solid stopping point for L-keys.
Extra: Common key sizes are stored in the holder where they are easily seen.
Blade: Chrome-vanadium steel, through-hardened, bronzed.
Based on ISO 2936L.
Content:
- 1x L-keys Hex , black oxidised 1.5 mm x 91 mm (06059)
- 1x L-keys Hex , black oxidised 2.0 mm x 101 mm (06361)
- 1x L-keys Hex , black oxidised 2.5 mm x 113 mm (06362)
- 1x L-keys Hex , black oxidised 3.0 mm x 128 mm (06363)
- 1x L-keys Hex , black oxidised 4.0 mm x 142 mm (06364)
- 1x L-keys Hex , black oxidised 5.0 mm x 163 mm (06365)
- 1x L-keys Hex , black oxidised 6.0 mm x 184 mm (06366)
- 1x L-keys Hex , black oxidised 8.0 mm x 206 mm (06368)
- 1x L-keys Hex , black oxidised 10.0 mm x 231 mm (06369)
- 1x Classic holder
Meets your requirements: Blue hammer head / soft: e.g. for furniture work and interior decorating, minor assembly. Yellow hammer head / medium-hard: e.g. for tool and machine engineering, car repairs, sheet metal and assembly work.
Simplifies your work: Makes work easier, optimum impact effect and less effort needed.
Lowers your costs: Ergonomic hickory wooden handle and hammer head both available as spare parts.
Product dimensions: 400 x 150 x 69 mm (LxWxD)
Application: Ideal for delivering measured positioning blows on components such as work pieces in machine vices or for installation work. Medium-hard hammer faces are eminently suitable for tool making and mechanical engineering, car repairs, and sheet metal and assembly work. Soft hammer faces for furniture manufacturing and interior fitting or minor assembly work.
Yellow hammer face (medium-hard) for tool manufacture / mechanical engineering, automobile sector, or sheet metal and assembly work
Blue hammer face (soft) for furniture manufacturing and interior fitting or minor assembly work
Recoiling impact effect minimizes the effort in a series of impacts
Protects the material being processed thanks to safety hammer faces
Hickory-wood handle and hammer faces available separately as spare parts
Depending on the site of operation, different hammer heads are needed to meet the specific requirements of various tasks. The recoilless, soft-faced hammer with hickory-wood handle makes it possible for the user to deliver measured positioning blows and protects delicate surfaces and edges due to its high-impact effect. Thanks to the special metal filling in the hammer head, the soft-faced hammer also guarantees absolutely no recoil, thus protecting joints. In addition, the approx. 25% greater mass of the hammer head ensures added power and easier work, optimum impact effect, and less effort needed as a result. The Safety Hammer is also distinguished by its high-grade hickory hammer handle with highly effective non-slip surface. The yellow, medium-hard hammer face with a diameter of 30 mm is ideal for universal use in areas like tool making and mechanical engineering as well as sheet metal and assembly work. The blue, soft hammer face also with a diameter of 30 mm is suitable for furniture manufacturing and interior fitting as well as minor assembly work. The hammer faces and the ergonomic hickory-wood handle are available as spare parts.
GS tested.
